Slewing Ring Bearing of Harbour Mobile Crane

By Gustavo Zamora*, Buenos Aires (Argentina) for gruasytransportes.

1 –
Liebherr large diameter bearing triple row roller bearing with external gear

ROD00657-021DA (Crédito: liebherr-bauma.com)

.
The slewing ring bearing of a harbour mobile crane is an element that we should take great care of due the cost of replacement, which between labor and spare parts constitutes a very important expense that can be avoided throughout the lifetime of the crane if we take the necessary care of it.
The slewing ring bearing of a harbour mobile crane is at the same time a triple row roller bearing and a giant turning gear crown with internal teeth similar to those of any other gear.
If the bolts that hold the slewing ring bearing are broken, or if the slewing ring bearing is broken, the crane can tip over.

2 – (Crédito- Credit: goimo.eu )

Slewing ring bearing with triple row of rollers with internal teeth, IMO brand.

This slewing ring bearing should not be heated since inside it there are cages that can be made of steel or brass, or plastic or polymers.
In the slewing ring bearing there are also rubber seals, or polymer seals that must be inspected periodically and protected from mechanical aggressions.
If an electric welding repair is carried out on the crane, the electric welding current must not pass through the slewing ring bearing at any time to prevent the bearing from being destroyed. This forces us so that the electrical connection of the electric welding machine must be placed very close to the place of the crane where we are going to carry out the welding repair..

3 – (Crédito- Credit: deutsche-grosswaelzlager.de )
Slewing ring bearing with triple row of rollers and with external teeth.

.
In this type of cranes the mentioned bearing is usually as we said one with a triple row of rollers. In other mobile construction cranes, in ship cranes and in offshore cranes, although their slewing ring bearings were other types of bearings, their slewing ring bearings require almost the same care as those of mobile harbour cranes.

4 – (Crédito-credit: deutsche-grosswaelzlager.de )

Slewing ring bearing with triple row of rollers and with external teeth

5 – (Crédito- Credit: deutsche-grosswaelzlager.de ).
Ship cranes.

6 – (Crédito- Credit: imo.de)
Slewing ring bearing with triple row of rollers and with external teeth.

Sources: gruasytransportes.

=============

How to extend the life of your slewing ring bearings)

.
Read it in English at : How to extend the life of your slewing ring bearings <http://www.kaydonbearings.com/downloads/whitepapers/Kaydon-BearingMaintWP.pdf>

Protect your investment

Premature failure is a common fate for large-diameter (e.g., 8" to 10') bearings in heavy-duty applications where rotations are frequent. In big rotating equipment such as cranes, excavators and tunnel boring machines, a slewing ring bearing must simultaneously handle a complex load spectrum that covers diverse combinations of thrust, radial and tilting moment loading.

Fortunately, there's an easy way to protect your investment in these custom-engineered bearings. It's called regular maintenance, and it can prevent 96% of slewing ring bearing failures. To maximize bearing life, simply follow these tips—raceway and gear lubrication, torque checks on bolts, and seal inspection—and be alert for four warning signs of potential bearing problems.

Picture. . (Credit: kaydonbearings.com )

Bearing lubrication

A bearing should be lubricated at regular intervals with heavy-duty, extreme-pressure grease. Apply a liberal shot to the fittings around the bearing's circumference at the interval recommended in the operator's manual.

Slowly-rotating equipment or oscillating applications (e.g., backhoes, excavators, cranes) should be re-lubricated about every 100 hours of operation. More frequent lubrication—every day or even every eight hours—may be needed on equipment that moves rapidly or rotates continuously, such as trenchers and boring machines.

While adding grease, the bearings should be rotated to spread the grease throughout. Pump it in until you see the old grease squeeze past the seal; this is called purging. Purged grease carries contaminants out of the bearing. Rub some between your thumb and forefinger...if you feel grit or metal chips, you may have a bearing problem.

Grease tends to dry out over long periods of time, allowing condensation to form within a bearing. You can avoid this by introducing grease at least every six months, even when the equipment is sitting idle.

Gear lubrication

Most large bearings have gear teeth that require lubrication, and those requirements are different than they are for the bearing itself. Since the meshing action of the teeth tends to squeeze out lubricant, gears should be lubricated every eight hours on slow-rotating or intermittently rotating equipment, and more often on rapidly or continuously rotating equipment. Small amounts of grease should be introduced at the point of mesh between the gear and pinion.

Seals

The seals on the bearing should be visually inspected periodically to be sure they are intact. Many people overlook the importance of seals, but they aid considerably in preventing bearing raceway contamination.

Bolts

A torque check on bolts should be part of any routine maintenance procedure. The frequency of these checks depends on the severity of service. Vibration and shock tend to loosen bolts, but periodic torque checks and tightening will help maintain the proper preload level.

Mounting bolts should be torqued to the proper level and checked periodically to ensure proper pre-tension. Improperly pre-tensioned bolts can fail, causing damage to equipment and, even more importantly, injuries to workers.

Bolt creep is another factor that should be monitored. Tightened bolts tend to creep or elongate over a period of time, reducing preload. Elevated temperatures can also increase bolt creep, so take this into consideration when developing a torque-check schedule.

Four warning signs of bearing problems

Regular maintenance goes a long way toward preventing premature failure, but even the most faithfully maintained bearings will eventually show signs of wear. To extend their life, look for these common signs and take corrective action as indicated

1. Play or clearance in the bearing often signifies that a raceway is worn. A new bearing is assembled with a specific amount of clearance to compensate for slight out-of-flatness in a mounting structure. Wear can increase this clearance dramatically. In machinery with a boom, free play magnified over the length of the boom allows it to rock back and forth under load, reducing the 'stiffness' in the extended boom. Check bearing clearance with a dial indicator that measures how much the structure tilts when the boom is loaded.

2. Grinding, popping, or clicking noises from the bearing typically mean there could be inadequate lubrication and/or excessive wear in the raceway, or loose bolts. As noted previously, greasing the bearing and purging lubricant is a good way to check for metal particles.

3. An increase in torque or binding can mean uneven wear in the raceway. If the turning torque of the bearing increases substantially or the bearing has tight spots, the load is probably unevenly distributed. With excavators, for example, the operator may sense a resistance to swing and find that the upper boom swings an inch or two past the point where it should stop. In advanced stages of wear, the bearing will pop and crack as the machine digs and swings.

4. Dimpled raceways are typically the result of overloading the bearing or repetitive, heavy loads. Even slight overloads can dimple a bearing race, and a dimple that starts at 1/1000th of an inch will almost always get bigger. The same goes for uneven loads. Lifting with a boom and undercarriage in the same position every time (such as curbside digging with an excavator) can dimple the bearing race near the uneven load. If possible, change the angle of approach from job to job.

Less wear means less expense

By monitoring the symptoms of bearing wear and doing regular preventive maintenance, you can significantly reduce the chances that a bearing will fail prematurely. This in turn minimizes expense because it keeps equipment working productively, avoiding breakdowns that lead to costly downtime and repairs.

Longer bearing life also means, of course, that bearings can be replaced less often, stretching budgets further. And when the time for replacement comes, consider having your old bearings remanufactured instead of buying new ones. Well-maintained bearings can typically be repaired for less than half the cost of a new replacement, if repaired before they fail. This is explained in another Kaydon white paper, How Bearings are Remanufactured.

Source:

kaydonbearings.com/downloads/whitepapers/Kaydon-BearingMaintWP.pdf

kaydonbearings.com/white_papers_4.htm

===========================

Any comments on this topic will be appreciated.

(*) Gustavo Zamora is a specialist in lifting equipment and cargo handling. Lives and works in Buenos Aires (Argentina)

Tags:

Slewing bearing Harbour Mobile Crane (gz38)(gz11), brass=latón,

Coronas de giro de Liebherr (gz11), bearing raceway = pista del rodamiento,

Grasa de engranajes abiertos mas aditivo bardahl maxima compresion para motores,

rocking test,

=============

Felixstowe Docker

Search This Blog